Home

You can select a Certification Programme from the list below to retrieve its description (scope of the programme, definitions...)

  See certified products


 
Scope of the programme

The programme scope covers the particulate and combination (particulate and gas) filters used in a residential ventilation unit and for which the following applies:

  • the rated maximum air flow rate is comprised between 70 and 1000 m³/h included ;
  • the initial efficiency ePM10 is higher than or equal to 50% ;
  • the initial efficiency ePM1 is strictly lower than 99%;      
  • the ratio between effluent and influent concentrations measured at time zero is strictly lower than 20% (for combination filters only, see Rating Standard RS/4/C/003 for further details).

The programme scope covers filters for which the face area is lower than or equal to 300 mm x 600 mm.

For the RFIL programme, the certify-all requirement as defined in the Certification Manual is applicable from 2020, January 1st (see Operational Manual OM-21 for further details).

Principle of the programme

The certification programme is based on product performance testing by independent testing laboratories according to the standards Eurovent 4/22:2015 (particulate filters and combination filters) and ISO 11155-2:2009 (combination filters only) as well as manufacturing facility auditing.

Definitions

Adsorption capacity

Mass of contaminant mc [mg] removed from the challenge gas stream by the filter.

Basic design

The basic design of a filter designates the arrangement of the filtering area which can be the following:

  • Bag : Media arranged in several bags
  • Panel : Media pleat which depth is < 150 mm
  • V-type : Media pleats arranged in several V-shaped rigid sections
  • Pleated : Deep media pleat (depth ≥ 150 mm)

Clean Air efficiency

The Clean Air Efficiency for Residential Air Filters (CAERFIL) can be defined as the amount of clean air delivered by the filter per unit of consumed energy [m3/h/kWh/a].

The Clean Air Efficiency is calculated from certified performance items:

  • initial efficiency ePM1 [-]
  • initial pressure drop Δp100% [Pa]

 

The Clean Air Efficiency is calculated as follows (see Rating Standard RS/4/C/003 for further details):



Combination filter

A combination filter designates a particulate filter which material or extra layer(s) present(s) additional filtration properties, intrinsically or after being treated or coated, such as gaseous filtration.

 

Filter family

A filter family is characterised by the following:

  • the same filter material
  • the same basic design
  • the same face velocity (rated airflow / minimum net filter face area)
  • the same
    • depth of the overall filter element, with a tolerance of +/-10% but not lower than 5 mm, for panel filters and pleated filters
    • ratio of filter medium area to front face area, with a tolerance of +/- 10%, for bag filters, V-type filters, pleated filters and panel filters
  • the same initial pressure drop, with a tolerance of +/- 10% but not lower than 5 Pa
  • the same ISO ePM class reporting value

Among these data, the following must be available via internet or published sales brochures: basic construction, filter media, ISO group for filter classification.

 

Initial efficiency

Efficiency of the clean filter operating at a given flow rate.

The symbol ePMx describes the initial efficiency of a filter element to reduce the mass concentration of particles with an optical diameter between 0,3 μm and x μm.

 

Initial pressure drop

Pressure drop of the clean filter operating at a given flow rate.

 

ISO ePMx class reporting value

Class reporting value, corresponding to the initial efficiency ePMx value rounded downwards to the nearest multiple of 5 percentage points, in conjunction with the group name.

Example: ISO ePM1 85%.

 

ISO groups for filters classification

The ISO groups for filters classification are defined as per document Eurovent 4/22:2015, excluding ISO Coarse which is not part of the RFIL certification programme scope.

 

Minimum efficiency

The symbol ePMx,min describes the minimum efficiency value of the conditioned (discharged) filter element, operating at a given air flow rate, to reduce the mass concentration of particles with an optical diameter between 0,3 μm and x μm.

 

Rated maximum airflow

Maximum operational air flow for the filter as recommended by the manufacturer. It is expressed in [m3/h].

 

Specific Energy Consumption of a residential air filter

The Specific Energy Consumption of a residential air filter (SECRFIL) is the expression of the energy consumed by the fan to overcome the pressure drop caused by the filter in a given Residential Ventilation Unit.

This value, expressed in [kWh/m2/a], is calculated from the initial pressure drop as follows (see Rating Standard RS/4/C/003 for further details):


Testing requirements

Tests shall be conducted on A4 format (i.e face dimensions 210 mm x 297 mm) filters, at the rated maximum airflow, according to the standards Eurovent 4/22:2015 (particulate filters and combination filters) and ISO 11155-2:2009 (combination filters only).

When testing combination filters the challenge gas shall be Toluene.

All tests will be performed in the independent laboratory(ies) selected by Eurovent Certita Certification.

Certified performance items and associated tolerances

When tested in the laboratory the obtained performance data shall not differ from the declared values by more than the following tolerance values:

Initial pressure drop values                        +10%+Mt or +10 Pa +Mt

Initial efficiency values                              -5 percentage points (absolute deviation)

Minimum efficiency values                          -5 percentage points (absolute deviation)

Filter ISO ePMx class reporting value            -5 percentage points (absolute deviation)

Adsorption capacity                                  -10%

Reference documents


Certification Manual 13th edition


Operational Manual OM-21-2017


Rating Standard RS/4/C/003-2017